GEPRC TAKER F405 BLS 100A 8S STACK｜飛控電變飛塔

GEPRC TAKER F405 BLS 100A 8S STACK｜飛控電變飛塔

GEPRC 官方飛控電變飛塔，已依台灣顧客使用習慣整理名稱、分類與付款方式。下單前請確認規格、接頭、頻段、極化方向、電壓及相關法規需求。

Changelog

Oct 20, 2025:

The flight control firmware has been changed to: [GEPRCF405_8S]. If you continue to use the [GEPRCF405_BT_HD] firmware for burning, you need to enter the following command in the CLI after burning the firmware:

resource SERIAL_TX 11 NONE

resource SERIAL_RX 11 NONE

set pinio_config = 1,1,1,1

set pinio_box = 32,41,255,255

save

Features

Use mainstream STM32F405 chip

Equipped with the latest 42688-P gyroscope

16M black box storage

Integrated LC filter

Upgrade type-C USB interface

Directly plugged into the DJI Air Unit

With TAKER H100_8S_BLS 100A 4IN1 ESC, Dual MOS, high current, silky flight

Supports 8S Lipo battery

Simple and reasonable installation method, the shock absorber can make the gyroscope work very stably

12V@3A + 5V@3A dual independent BEC

Specifications

GEP-F405-8S Flight Controller

MCU: STM32F405

IMU: ICM42688-P(SPI)

Air Unit Connection: Direct plugging into DJI Air Unit

Black Box: 16M onboard

Barometer: support

Motor outputs: M1-M8

USB Interface: Type-C

OSD: BetaFlight OSD w/ AT7456E chip

BEC: 5V@3A,12V@3A dual BEC

Firmware Target: GEPRCF405_8S

Size: 37x37mm

Mounting: 30.5×30.5mm，φ4mm hole becomes φ3mm after using a silicone shock-absorbing circle

Input Voltage: 3-8S LiPo

UART: 6 UARTs

Power Filter: Integrated LC filter

Weight: 8.3g

TAKER H100_8S_BLS 100A 4IN1 ESC

Input Voltage: 3-8S Lipo

Ammeter: Support

Calibration value: 200

Continue Current: 100A

Burst Current: 105A（5 second）

Support Protocol: Dshot 150/300/600

Size: 56.3*61.1mm，hole30.5×30.5mm，φ4mm hole becomes φ3mm after using the silicone shock-absorbing ring.

Weight: 28.8g

Target: B_X_3

Includes

1 x GEP-F405-8S Flight Controller

1 x TAKER H100_8S_BLS 100A 4IN1 ESC

1 x Electrolytic capacitor(50V 4700uF)

1 x DJI connection cable(SH1.0 6pin 100mm)

2 x FC adapter cable(SH1.0 8pin 30mm)

1 x Receiver silicone cable(SH1.0 4pin 150mm)

1 x Camera connection cable(SH1.0-SH1.25 3pin 135mm)

1 x VTX connection cable(SH1.0 4pin-6pin 100mm)

1 x XT90 battery plug

1 x Red and black power cable(10AWG 240mm)

4 x M3*30 screws

4 x M3*25 screws

8 x Nylon nuts(M3)

12 x Silicone anti-shake pads(M3)